West Elm Leather Sling Side Table Knock Off

I was needing a little table at the end of my sofa.  I had purchased a little garden stool that worked perfectly, until I put a drink on it and realized the top wasn’t quite flat and level.  I also love perusing magazines and try and read them when I have some downtime.  A busy summer means I have back months of magazines to still read and I wanted a place where they would still be visible so I wouldn’t forget to read them.  When I saw the $299 West Elm Leather Sling Table I decided to create a similar one with a more industrial vibe that would reflect my style a bit more.  Plus my garage is busting at the seams with scrap wood that I knew would be free to use for this project.  I ask my dear friend’s son to help me with this project since he has been wanting to learn more about woodworking.free plans for a west elm inspired magazine sling end table west-elm-inspired-magazine-sling-table

Subscribe To Download Plans


Enter your email and the West Elm Magazine Sling Table Plans will be sent to your inbox!

100% Secure. Powered by ConvertKit


1″ x 3″ x 6′

2″ x 2″ x 8′

1″ x 2″ x 6′

3/4” 2′ x 4′ oak or birch plywood (top)

1/4” x 1” (plywood edge finish)

Extra supplies:

chop saw and table saw

1/2” spade bit

threaded 1/2” rod

4 acorn nuts and 4 washers

Kreg Jig

1 1/4” pockethole screws

finishing supplies



pleather fabric (I got mine from Jo-Ann Fabrics)

sewing machine and coordinating thread

optional: corner brace and upholstery tacks

1.  Cut out your all your pieces except for the plywood top. I also like to sand all the pieces with 120 grit sandpaper before assembly.

2. Drill a 1/2” hole into your 2”x 2” pieces.  I used a drill press to get a nice straight hole.  But using a hand drill would work too.  Just make sure you aren’t accidentally drilling it in at an angle.


3.  Screw the side pieces into your legs leaving a 1/4” gap in the front of the table.  Using a 1/4” scrap piece of wood and setting it under your 1” x 3” while you screw it in will give you that inset. Note: Make sure you pay attention to the direction of the pocketholes making sure they going upward so you can screw in your tabletop later.



4.  Measure the length and width of your base and cut the plywood piece that size.  Flip your table over and use 1 1/4” pockethole screws to attach the base to the plywood top.


5.  To finish the plywood edge you can either use iron-on edge banding or rip some 1/4” x 1” strips from scrap wood and cut and nail them in place.  Since I wanted it to overhang just a little I opted for this route.


6.  Next add your stretchers.

DIY-magazine-end-table   end-table-magazine-holder

7. Cut a metal threaded rod to fit leaving about 1/2” beyond the table.

8.  Finish your table.  I filled all the nail holes, sanded my table smooth, wiped it down and applied Minwax Pre-Stain Conditioner to the entire piece. Then 5 minutes later I wiped it again and stained it with one coat of Minwax Special Walnut.  After 10 minutes I wiped it down again.  After 8 hours I applied a coat of Minwax Wipe-On Polyurethane.  I let it dry and then sanded between coats and added about 2-4 coats total (2 to the base and 4 to the top of the table).

9.  Sew your magazine sling.  Cut a piece of fabric 18” x 48”.  Fold right sides together and use binder clips to hold it in place while you sew.



10.  Sew 1/2” seam allowance leaving a hole for turning.  Clip corners. Turn inside out.  Finger press, binder clip and top stitch.  Then fold under your two 17” sides under 1” and sew a casing for the threaded rod.


11.  Slide the threaded rods in place through the casing on the magazine sling.  Secure with a washer and an acorn nut.


12.  Optional:  To add some industrial details add a 1/2” metal angle to both corners.  I used an upholstery tack pounded in with a rubber mallet to hold the angles in place.  The details totally matches the 2×4 farmhouse industrial end table I built on the other side of the couch.


Now I have a place to set a drink and a place to store all my magazines.  Dual purpose is my fave.

magazine-table (2)




end-table-magazine-holder (2)

For more building plans check out…

2 x 4 Industrial End Table Cart

Build an industrial end table cart for $20 using only 2x4s

2 x 4 Hallway Console Table


West Elm Inspired Media Cabinet


Download Free Plans for a Double Sliding Barn Door!


Enter your email and the DIY Barn Door Plans will be sent to your inbox!

100% secure. Powered by ConvertKit