matchbox race track promo

I am floored by this amazing idea from Brittany from Pretty handy Girl.   Using building scraps she had on hand she created this kick awesome matchbox racetrack for her two boys.   My son would be over the moon with this.   I am so putting this on my father-in-laws list to make for Isaac.   Brilliant gift idea!

PennyWisePresents

Thanks for inviting me to Pennywise Presents Beckie. I’m thrilled to share with you a gift idea for the little toy car fans in your life.

 Matchbox Cars Track If you have boys, I’m sure you have Matchbox cars in your home. They go hand-in-hand. My boys play with their race cars for hours!

They have several of the plastic Matchbox tracks. And even a curly-Q racing ramp. But, honestly they seem to play with my scrap pieces of wood more than the plastic tracks. Chances are, if you or your spouse build things, you will have all the scraps of wood on hand to make this racing ramp.

My 7 year old and I worked together on this project. (He was my design consultant and he also helped with some of the assembly.) But, imagine the surprise on a child’s face if you made this ramp as a holiday or birthday gift!

Supplies:

  • 2 – 1 x 4 x 13″ boards (tower sides)

  • 1- 1 x 4 x 9″ board (tower roof)

  • 2 – 1 x 8 x 33″ boards (ramp sides)

  • 1 – 1 x 6 x 33″ board (ramp)

  • 1 – 3/4″ dowel rod (cut to 12″)

  • 1 – 1/8″ dowel rods

  • 1 – thin rectangular strip for a divider 33″ long

  • 1 5/8″ screws

  • 1″ finish nails

  • 2″ finish nails

  • Gorilla Glue

  • Sandpaper

  • Primer

  • Spray paint

  • ScotchBlue Painter’s Tape

  • X-acto knife

  • Clamps

  • Cordless drill

  • Handsaw or miter saw

  • 3/4″ spade bit

  • 1/8″ drill bit

Start by cutting all your boards to length. Grab the ramp board (1 x 6 x 33″) and cut one end of the ramp at a 30Ëš angle. Glue the narrow strip onto the center of your ramp using a small amount of Gorilla Glue. Clamp the strip and add a few 1″ finish nails to secure the strip. Set up your boards as shown. Tilt the ramp up at the back, the angled cut will rest on the floor (not shown.) Drive a few screws through the side walls and into the ramp with your drill. Line up the tower sides approximately 2″ from the back edge of the ramp walls. Then secure them in place with a few more screws. Drill a hole into each tower side large enough for the 3/4″ dowel rod to fit through. Slide the dowel rod through and center it on the ramp. Mark the location of the center of the left and right tracks onto the dowel rod. Measure the distance between the dowel rod and the ramp. Use this measurement to cut 2 pieces of 1/8″ dowel rod 1/2″ longer than that measurement.

Remove the 3/4″ dowel rod. Drill holes 1/8″ wide halfway through the big dowel rod at the locations you marked for the centers of the tracks.) Wrap a piece of painter’s tape around the drill to indicate a depth 2/3 of the way through the 3/4″ dowel rod. Then don’t let the bit go further than the tape into the rod.

Mark the location where the dowel meets the outside of the tower wall. Drill a hole all the way through the large dowel rod. Insert the 3/4″ dowel rod through the holes in the tower walls. Glue the 1/8″ cut dowels into the halfway holes. Then cut and glue two more 1/8″ dowels to go through the 3/4″ dowel on the outside of the tower walls. These will anchor the large dowel rod and keep it from slipping out of alignment. Nail finish nails through the tower roof and into the walls of the tower. That completes the building portion of this tutorial. Hopefully your ramp resembles this one: Now it is time to add some pizzazz! Ka-chow! My design consultant demanded fiery red flames and black on his ramp. (And what he wants, he gets!) I lightly sanded the wood race track. Added a coat of primer and some red and yellow spray paint. Then I cut out a flame design using ScotchBlue painter’s tape (4 pieces overlapping) and an x-acto knife on a cutting board. I gently lifted the tape and adhered it to the side walls. After a coat of metallic hammered metal spray paint, I removed the tape to reveal: matchbox cars ramp What do you think? Do I have a shot at a job on Orange County Choppers??!! The “logo” on the top was made by pressing letter stickers over the primer, then I taped off around the words and sprayed some red and yellow spray paint. The lines are made with black graphic adhesive lines. matchbox cars ramp On your marks…get set… matchbox cars rampand GO!matchbox cars ramp Nice two wheel stunt!hot wheels track I hope you will make one of these for your little stunt driver. I want to extend an invitation for you to visit me on my blog, Pretty Handy Girl. You will find tutorials for everything from sewing (like these little gift pouches).

  to home improvement projects (like building a hallway storage towers and shoe storage bench) and home repairs (like common toilet repairs)! Happy Holidays and enjoy the rest of Infarrantly Creative’s Pennywise Presents!

 

Similar Posts

12 Comments

  1. Brittany’s tutorials are absolutely awesome, and this one is just fantastic! My boys would have LOVED this. Now that my “boys” are all bigger than I am, I probably won’t be making one–but I have to admit I’m tempted! What a fun thing to open on Christmas morning! 🙂

  2. Pingback: Cars « lvbaby

Leave a Reply

Your email address will not be published. Required fields are marked *